design refer to ul60950-1 iec60950-1,en60950-1, compliance to en55022 (cispr22) class b,en61000-3-2,en61000-3 -3 i/p-o/p:3.0kvac i/p-fg:1.5kvac o/p-fg:0.5kvac compliance to en61000-4-2,3,4,5,6,8,11; en55024, light indust ry level (surge 4kv), criteria a short circuit protection type : hiccup mode, recovers automatically after fault co ndition is removed protection type : hiccup mode, recovers automatically after fault co ndition is removed protection type : shut down o/p voltage with auto-recovery or re-power on t o recovery i/p-o/p, i/p-fg, o/p-fg:100m ohms/500vdc/ 70%rh 25 / file name:usp-150-spec 2012-02-04 150w 150w 151.2w rated power 151.2w 11.0~13.2v 13.5~16.5v 21.6~26.4v voltage adj. range 32.4~39.6v 130~185% rated output power specification model dc voltage rated current output line regulation load regulation setup, rise time hold up time (typ.) voltage range note.4 frequency range power factor (typ.) efficiency (typ.) input inrush current (typ.) leakage current over temperature safety standards working temp working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing overload over voltage ac current (typ.) 2000ms, 100ms/230vac 3000ms, 100ms/115vac at full load 90 ~ 295vac 127 ~ 417vdc 47 ~ 63hz 2a/115vac 1a/230vac 0.7a/277vac cold start 65a/230vac <2ma / 240vac 13.6 ~ 16.3v 17 ~ 21v 26.7 ~ 32.4v 100 5 (rth2) protection type : shut down o/p voltage, recovers automatically afte r temperature goes down -30 ~ +65 (refer to output load derating curve) 20 ~ 90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh 0.03%/ (0 ~ 60 10 ~ 500hz, 2g 10min./1cycle, 60min. each along x, y, z axes 216.3k hrs min. mil-hdbk-217f (25 ) 215*67.4*33mm (l*w*h) 91.5% 16ms/230vac 16ms/115vac at full load 91.5% 93% 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 2.0% 2.0% 2.0% 100mvp-p 150mvp-p 150mvp-p 12v 12.5a 0 ~ 12.5a 15v 10a 0 ~ 10a 24v 6.3a 0 ~ 6.3a usp-150-12 USP-150-15 usp-150-24 150w u-bracket single output with pfc function features : u s p - 1 5 0 s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment safety & emc (note 5) protection withstand voltage note.6 isolation resistance current range 41.4 ~ 48.6v 93% 1.0% 0.5% 2.0% 250mvp-p 36v 4.2a 0 ~ 4.2a usp-150-36 153.6w 43.2~52.8v 53 ~ 64.8v 93% 1.0% 0.5% 2.0% 250mvp-p 48v 3.2a 0 ~ 3.2a usp-150-48 universal ac input / full range(up to 295vac)built in active pfc function constant voltage design high efficiency up to 93% protections: short circuit / overload / over voltage / over temperature cooling by free air convection u-bracket low profile:33mm zvs technology to reduce power dissipation 3 years warranty 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. derating may be needed under low input voltages. please check the static c haracteristics for more details. 5. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still mee ts emc directives. 6. please remove the component d1 before conducted hipot test. pf 0.98/115vac pf 0.96/230vac pf 0.94/277vac at full load 0.48kg; 24pcs/12.5kg/0.61cuft emc immunity emc emission
block diagram mechanical specification derating curve case no. 988 unit:mm u s p - 1 5 0 s e r i e s ac input connector (cn1) :svh-21t-p1.1 or equivalent pin no. 1 23 assignment fg ac/l ac/n mating housing jst svh-21t-p1.1 or equivalent terminal 150w u-bracket single output with pfc function file name:usp-150-spec 2012-02-04 cn1 2 1 3 pwm circuit detection o.l.p. emi filter apfc power switch- filter & synchronous +v i/p fg ing converter o.v.p. bridge rectifiers -v o.t.p. controller rectifiers 215 52 62.7 201 211 67.4 33 3.5 4pl ambient temperature ( ) load (%) -30 0 10 20 30 40 50 60 65 70 20 40 60 80 100 (horizontal) 130 55 45 jst vhr or equivalent mount with a 300*500*2mm heatsink static characteristics input voltage (v) 60hz 90 100 110 135 155 230 295 100 90 80 70 60 50 40 load(%) 100vac 230vac 194 208 6.5 3.5 3.5 4.5 4pl cn2 7.62 1 2 3 4 dc terminal pin no. assignment (cn2) pin no. 1,2 3,4 assignment v- v+ terminal t21-bm10-04 deca
|
